When you prepare pipe ends for welding, three dimensions appear on almost every welding procedure specification: bevel angle, root face and root gap. They all describe the same small zone at the end of the pipe, yet each one is controlled at a different stage of the work. Knowing which stage controls which dimension is the key to consistent joints without rework. For the full sequence from raw pipe to fit-up, see the complete cutting and beveling workflow.
What Bevel Angle, Root Face and Root Gap Each Do
The bevel angle is the angle machined onto the pipe end, measured from a line perpendicular to the pipe axis. It opens the weld groove so the welder can reach the root and fuse the full wall. When both ends carry the same bevel, the included groove angle is twice the bevel angle: two 37.5° bevels give 75°. A wider angle gives easier access but needs more filler metal. The required value comes from the welding procedure specification (WPS).
The root face, also called the land, is the small flat unbeveled strip left at the tip of the pipe end. It gives the arc solid metal to start on instead of a thin feathered edge that would burn away. The root face is specified in the WPS and is produced during the beveling operation.
The root gap is the distance between the two pipe ends once they are positioned and tacked. It only exists after two prepared ends are brought together, so it is set at fit-up by the fitter, not by the beveling machine. The WPS gives an acceptable range, and it is checked with a gauge before welding.
What Beveling Equipment Controls, and What It Does Not
A pipe beveller controls the bevel angle, through the cutting head fitted, and the bevel depth, which together with the wall thickness determines the remaining root face. On the Pipe Beveller 220E and 360E, the angle comes from the cutting head (30°, 37.5° or 45°, with tailored angles on request). The built-in stopper lets the operator repeat the same bevel on pipes with the same outside diameter.
The machine does not control the root gap. Once both ends carry the correct bevel and root face, the fitter assembles the joint, sets the gap and checks it against the WPS. Even perfectly beveled ends can be fitted with a gap that is too tight or too wide, so all three dimensions must be checked.
| Dimension | Definition | Set by | Produced at | Checked with |
|---|---|---|---|---|
| Bevel angle | Angle of the machined face from perpendicular | WPS | Beveling: cutting head angle | Bevel gauge or protractor |
| Root face | Flat unbeveled land at the pipe-end tip | WPS | Beveling: bevel depth against wall thickness | Caliper or weld gauge |
| Root gap | Opening between two assembled pipe ends | WPS | Fit-up and tacking | Feeler or weld gauge |
What Remains a Procedure, Setup or Fit-Up Decision
The values for all three dimensions are prescribed by the WPS, which has been qualified to meet the applicable code. Working outside the WPS tolerance can invalidate the procedure, which is why it matters which stage controls which dimension.
Machine setup is decided before beveling starts. The operator fits the cutting head for the angle, sets the bevel depth for the required root face, checks the first pipe and then repeats the setting with the stopper on pipes of the same OD. Fit-up is decided at assembly, where the fitter accounts for ovality and alignment and sets the gap within the WPS range. For groove types, see our complete guide to pipe beveling. For machine setup, see our guide to using a pipe beveling machine.
Frequently Asked Questions
What is a root face in welding?
The root face, or land, is the small flat unbeveled strip at the tip of a beveled pipe end. It gives the root pass solid metal to start on, and its size is set in the WPS.
What is the root gap?
The root gap is the opening between two pipe ends after fit-up. It is set by the fitter within the range given in the WPS.
Does a beveling machine set the root gap?
No. The machine produces the bevel angle and root face on each pipe end; the gap is set when the two ends are fitted together.
Controlled Bevel Production With Exact Tools
Our pipe bevellers produce the two dimensions a machine can control: the bevel angle, through 30°, 37.5° and 45° cutting heads, and repeatable bevel depth, through the built-in stopper. The Pipe Beveller 220E covers 25 to 220 mm and the 360E 110 to 360 mm, both up to a 10 mm steel wall. Exact Tools holds ISO 9001, ISO 14001 and ISO 45001 certification. Send us your specified geometry and we will help you match the machine and cutting head to your bevel angle and root face.