PipeCut P400E vs P1000 vs V800E: choosing a plastic and ventilation saw

The PipeCut P400E, PipeCut P1000 and PipeCut V800E are not competing for the same work. Two of them cut plastic pipe at different diameters, and the third cuts thin-wall stainless spiral ventilation duct. Your material and pipe diameter make the choice. For the full range, see our complete pipe saw model comparison.

Three Machines, Three Different Jobs

  • Cutting and beveling plastic pipe from 50 to 400 mm in one pass: the P400E.
  • Cutting PP, PE, PVC and HDPE pipe from 60 to 1000 mm, with walls up to 75 mm: the P1000.
  • Cutting stainless spiral ventilation duct from 75 to 800 mm: the V800E.

Comparison of the Three Machines

Specification P400E P1000 V800E
Pipe OD 50 to 400 mm 60 to 1000 mm 75 to 800 mm
Max wall 25 mm (22 mm with Cut&Bevel) 75 mm with TCT P250 1.5 mm (6 mm at the seam)
Materials Plastic pipe such as PE, PP, PVC PP, PE, PVC, HDPE Stainless ventilation pipe, spiral duct
Holding Solid rubber tire wheels instead of a gripper unit, so the pipe is not marked
Speed 1600 to 3500 rpm 1900 and 2885 rpm 1600 to 3500 rpm
Blade fitted TCT P150, plus Cut&Bevel blade 148 TCT P190 Cermet V155
Cut and bevel in one pass Yes, 15°, blade included Yes, 15°, with Cut&Bevel blade 190 (sold separately) No
Weight 6.0 kg 11.5 kg 6.0 kg
Extras Lower blade guard that closes instantly off the pipe Lower blade guard, traffic light system, laser indicator, vacuum port Optional supports for spiral duct

PipeCut P400E: Cut and Bevel Up to 400 mm

PipeCut P400E plastic pipe saw

The P400E cuts plastic pipe from 50 to 400 mm and makes a 15° bevel in the same pass with the included Cut&Bevel blade 148. It can also run cut only or bevel only. Rubber tire wheels carry the saw around the pipe without marking it. It comes with two P400 Single supports and one P400 Double, rated at 260 kg with three supports. A cordless P400 Battery covers the same diameters with a 20 mm wall limit (18 mm with cut and bevel). See our corded vs battery comparison.

PipeCut P1000: Plastic Pipe Up to 1000 mm

PipeCut P1000 for plastic pipe up to 1000 mm

The P1000 cuts PP, PE, PVC and HDPE pipe from 60 to 1000 mm. With the TCT P250 it handles walls up to 75 mm. The Cut&Bevel blade 190 adds a 15° bevel in the same pass on walls up to 40 mm. The lower blade guard closes instantly when the blade loses contact with the pipe. The laser indicator shows the cutting point, the traffic light system supports precision, and the vacuum port takes an industrial vacuum.

PipeCut V800E: Thin-Wall Spiral Ventilation Duct

The V800E is built for stainless spiral ventilation duct from 75 to 800 mm, with a 1.5 mm wall (6 mm at the seam). It runs only with the Cermet V155, which has a 65 mm bore and must not be used on other machines. Optional special supports are available for spiral duct from 75 to 800 mm. The V800E replaces the earlier V1000. Our article on why thin-wall duct needs a different saw explains the difference.

Blade Selection for Each Machine

Blade Diameter Made for Machines
TCT P150 150 mm Plastic pipe Fitted to the P400E and P400 Battery
TCT P190 190 mm Plastic pipe Fitted to the P1000
TCT P250 250 mm Plastic pipe, walls up to 75 mm P1000 only
Cut&Bevel blade 148 148 mm Cut and 15° bevel, walls up to 22 mm P400E, P400 Battery, P1000
Cut&Bevel blade 190 190 mm Cut and 15° bevel, walls up to 40 mm P1000 only
Cermet V155 155 mm Very thin pipe walls, ventilation duct V800E only

For blade choice by plastic type, see cutting HDPE, PE, PP and PVC pipe. For technique, see our guide to cutting plastic pipe clean and square.

Which Machine for Which Trade

  • HVAC and ventilation: the V800E for spiral duct.
  • Water and sewer: the P400E for pipe up to 400 mm, and the P1000 for larger PE and PVC mains up to 1000 mm.
  • Drainage and stormwater: the P1000 for large-diameter PVC and HDPE pipe.
  • Industrial process plastics: the P1000 with the TCT P250 for walls up to 75 mm.

Whether a pipe end needs a bevel depends on the joining method; see cut only or cut and bevel plastic pipe.

Frequently Asked Questions

Does the P400E use a gripper?

No. The P400E, P1000 and V800E all use solid rubber tire wheels instead of a gripper unit, so the pipe surface is not marked.

Can the V800E cut plastic pipe?

The V800E is built for stainless spiral ventilation duct and runs only with the Cermet V155. For plastic pipe, use the P400E or P1000.

Which saw cuts the thickest plastic wall?

The P1000, up to 75 mm with the TCT P250.

Choose the Right Machine With Exact Tools

Browse the plastic and ventilation range, or send us your pipe material, diameter and wall thickness and we will confirm the right machine and blade. You can also find a dealer on our distributors page.

Share this post

Contact Us

Contact